{"product_id":"mxo-racing-mini-z-evo-4g-futaba-receiver-conversion-4ch-receiver-module-mxo-racing-evo-rx-f4g","title":"MXO Racing MINI-Z EVO 4G Futaba Receiver Conversion 4CH Receiver Module [MXO RACING] EVO-RX-F4G","description":"\u003cp\u003e\u003cspan\u003eThe MX EVO 4G is a FUTABA -4G compatible ultra - miniature receiver for KYOSHO's MR -03EVO and MA -03EVO , with an output speed of up to 3 .4ms in EVO mode . It can work not only in EVO mode , but also in 4CH PWM standard signal mode .\u003c\/span\u003e\u003cbr\u003e\u003cspan\u003eFeatures ：\u003c\/span\u003e\u003cbr\u003e\u003cspan\u003eSize: 13 . 5*10 . 0*3 . 5mm;\u003c\/span\u003e\u003cbr\u003e\u003cspan\u003eWeight: 0 . 58g;\u003c\/span\u003e\u003cbr\u003e\u003cspan\u003eWorking voltage: 3 . 0V or 3 . 3V;\u003c\/span\u003e\u003cbr\u003e\u003cspan\u003eCompatible with Futaba -SFHSS protocol;\u003c\/span\u003e\u003cbr\u003e\u003cspan\u003eSupport EVO and 4CH PWM two working modes;\u003c\/span\u003e\u003cbr\u003e\u003cspan\u003eThe output speed in EVO mode is 3 .4ms;\u003c\/span\u003e\u003cbr\u003e\u003cspan\u003eThe output speed in 4CH PWM mode is 3 .4\/6 . 8ms;\u003c\/span\u003e\u003cbr\u003e\u003cspan\u003eSupport online firmware upgrade .\u003c\/span\u003e\u003cbr\u003e\u003cspan\u003eBind Operation:\u003c\/span\u003e\u003cbr\u003e\u003cspan\u003eInstall the MX EVO RX first , then power on the receiver and press the BIND switch until the red LED on the RX changes from slow flashing to fast flashing .\u003c\/span\u003e\u003cbr\u003e\u003cspan\u003ePower on the transmitter , then set it to SFHSS mode (if it is already in SFHSS mode , ignore this step) , wait for a few seconds , when the LED on the receiver changes from fast flashing to steady light , it means BIND is successful and the receiver is already in normal mode .\u003c\/span\u003e\u003cbr\u003e\u003cspan\u003eRed LED status indication:\u003c\/span\u003e\u003cbr\u003e\u003cspan\u003eThe red LED on the MX EVO RX is an indication of the working status of the RX:\u003c\/span\u003e\u003cbr\u003e\u003cspan\u003e1) When the red LED flashes slowly , it means that RX is waiting to receive a signal;\u003c\/span\u003e\u003cbr\u003e\u003cspan\u003e2) When the red LED flashes quickly , it means RX is in BIND mode;\u003c\/span\u003e\u003cbr\u003e\u003cspan\u003e3) When the red LED is always on , it means that the RX has received the signal stably .\u003c\/span\u003e\u003cbr\u003e\u003cspan\u003eGreen LED status indication:\u003c\/span\u003e\u003cbr\u003e\u003cspan\u003eThe green LED on the MX EVO RX is an indication of the RX operating mode:\u003c\/span\u003e\u003cbr\u003e\u003cspan\u003e1) When the green LED is on , it means the RX is working in EVO mode;\u003c\/span\u003e\u003cbr\u003e\u003cspan\u003e2) When the green LED is off , it means that the RX is working in 4CH PWM mode;\u003c\/span\u003e\u003cbr\u003e\u003cspan\u003eHow to set up the transmitter (when MX EVO RX is used on MR -03EVO\/MA -03EVO):\u003c\/span\u003e\u003cbr\u003e\u003cspan\u003eBecause the brushless ESCs and servos on MR -03EVO\/MA -03EVO cannot set the midpoint and end point , the user can only set the transmitter to adapt to the parameters of MR -03EVO\/MA -03EVO . The settings are as follows:\u003c\/span\u003e\u003cbr\u003e\u003cspan\u003e1）TH TYPE    \u0026gt;   F5 : B5\u003c\/span\u003e\u003cbr\u003e\u003cspan\u003e2）EAP: ST \u0026gt;L150% R150%\u003c\/span\u003e\u003cbr\u003e\u003cspan\u003eTH \u0026gt;H150% B150%\u003c\/span\u003e\u003cbr\u003e\u003cspan\u003e3）D\/R:  ST \u0026gt;100%\u003c\/span\u003e\u003cbr\u003e\u003cspan\u003eTH \u0026gt;100%\u003c\/span\u003e\u003cbr\u003e\u003cspan\u003e4）REV: ST \u0026gt;REV\u003c\/span\u003e\u003cbr\u003e\u003cspan\u003eTH \u0026gt;REV\u003c\/span\u003e\u003cbr\u003e\u003cspan\u003eNote: Points 2 and 3 can be adjusted according to user habits .\u003c\/span\u003e\u003cbr\u003e\u003cspan\u003eHow the MX EVO RX works in EVO mode:\u003c\/span\u003e\u003cbr\u003e\u003cspan\u003eWhen users install MX EVO RX on KYOSHO's MR -03EVO\/MA -03EVO frame or other products that support EVO mode , MX EVO RX will work in EVO mode .\u003c\/span\u003e\u003cbr\u003e\u003cspan\u003eIn EVO mode , when the MX EVO RX is just powered on , the LED on the RX will not flash quickly , but the green LED will light up .\u003c\/span\u003e\u003cbr\u003e\u003cspan\u003eNote: When using the MX EVO RX on the MR -03EVO\/MA -03EVO , be sure to install it in place , otherwise you may burn it; if necessary , place the receiver compartment cover on the MR -03EVO\/ MA -03EVO Add a small piece of sponge to hold down the MX EVO RX .\u003c\/span\u003e\u003cbr\u003e\u003cspan\u003eHow the MX EVO RX works in 4CH PWM mode:\u003c\/span\u003e\u003cbr\u003e\u003cspan\u003eWhen users install MX EVO RX on EVO - BA1 or other products that support 4CH PWM mode , MX EVO RX will work in 4CH PWM mode .\u003c\/span\u003e\u003cbr\u003e\u003cspan\u003eIn 4CH PWM mode , when the MX EVO RX is just powered on , the LED on the RX will flash several times quickly and then enter the working mode , but the green LED will be off .\u003c\/span\u003e\u003cbr\u003e\u003c\/p\u003e","brand":"GRIDZ Raceway","offers":[{"title":"Default Title","offer_id":48481189167333,"sku":null,"price":64.99,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0793\/4764\/6693\/files\/mxo-racing-mx-evo-seriesmr-03evoma-03evoevo4ch-pwm.jpg?v=1772329043","url":"https:\/\/gridzraceway.com\/products\/mxo-racing-mini-z-evo-4g-futaba-receiver-conversion-4ch-receiver-module-mxo-racing-evo-rx-f4g","provider":"GRIDZ Raceway","version":"1.0","type":"link"}